zappi v2Technical Support & Specifications
- Technical Specifications
- Technical Support
1. Technical Specifications
|Mounting Locations||Indoor or Outdoor (permanent mounting)|
|Charging Mode||Mode 3 (IEC 61851-1 compliant communication protocol)|
|Display||Graphical backlit LCD|
|Front LED||Multicolour, according to charge status, current and user setting|
|Charging Current||6A to 32A (variable)|
|Dynamic Load Balancing||Optional setting to limit current drawn from the unit supply or the grid|
|Charging Profile||3 charging modes: ECO, ECO+ or FAST. STOP is a further option|
|Connector Type||Type 2 tethered cable (6.5m) or type 2 socket with locking system|
|Compliance||LVD 2014/35/EU, EMC 2014/30/EU, EN 62196-2:2017, IEC 62955:2018, ROHS 2011/65/EU, CE Certified
* -T variant is fully compliant with EN 61851-1:2019
Zappi versions that do not have the -T suffix comply with EN 61851-1:2019 with the exception of Clause 8.4 in order to meet the requirements of BS 7671:2018 Amendment 1:2020 which requires the protective earth conductor to be switched in order to provide protection against a damaged PEN conductor in a TN-C-S earthed electrical system
|Rated Power||7kW (1-ph) or 22kW (3-ph)|
|Rated Supply Voltage||230V AC Single Phase or 400V AC 3-Phase (+/- 10%)|
|Rated Current||32A max|
|Standby Power Consumption||3W|
|Earth Leakage Protection||Integral 30mA Type A RCD + 6mA DC protection (IEC 62955)|
|Economy Tariff Sense Input||230V AC sensing (4.0kV isolated)|
|Wireless Interface||868 MHz / 915 MHz (-A units) proprietary protocol for wireless sensor and remote monitoring options|
|Grid Current Sensor||100A max. primary current, 16mm max. cable diameter|
|Supply Cable Entry||Rear / Bottom / left side / Right side|
|Enclosure Dimensions||439 x 282 x 122mm|
|Protection Degree||IP65 (weatherproof)|
|Enclosure Material||ABS 6 & 3mm (UL 94 flame retardant) colours: white RAL 9016 and grey RAL 9006|
|Operating Temperature||-25°C to +40°C|
|Fixing Points||In-line vertical mounting holes|
|Weight||Single Phase Untethered: 3.0kg
Single Phase Tethered: 5.5kg
Three Phase Untethered: 3.3kg
Three Phase Tethered: 7.2kg
|ECO||Charge power is continuously adjusted in response to changes in generation or power consumption elsewhere in the home.
Charging will continue until the vehicle is fully charged, even if power is drawn from the grid.
|ECO +||Charge power is continuously adjusted in response to changes in generation or power consumption elsewhere in the home.
Charging will pause if there is too much imported power, continuing only when there is sufficient surplus power available.
|FAST||In this mode, the vehicle will be charged at maximum power. This is just like an ordinary Mode 3 charging point.|
|Variants with (-A) have specific hardware for the wireless interface to operate in the 915MHz band instead of the 868MHz band|
Designed to permit installations compliant with IET Wiring Regulations BS 7671:2018 amendment 1:2020 and the Electricity Safety, Quality, and Continuity Regulations 2002 and BS 8300:2009+A1:2010.
2. Technical Support
If you experience any issues with your zappi during or post installation, please contact our technical support team:
0333 300 1303
Mon-Thu 9.00am – 5.00pm
Fri 9.30am – 5.00pm
Our experienced engineers will be pleased to assist and to help solve your issues over the phone.
Please contact us directly for the quickest solution.