Shopping Bag

×

 

Setting up a replacement hub

If you receive a replacement hub you will need to follow these steps

  1. First you need to delete the old hub on your eddi and/or zappi, then
  2. Make sure that the new hub has the latest firmware installed before
  3. Pairing  the new hub.

Please follow the instructions below.  If you run into any problems please contact our technical support team at support@myenergi.uk

(1) Deleting the old hub from the master device

Note – If you have more than one myenergi device you only need to do this on the Master device (shown with an M next to it on the Linked Devices screen)

To find out which device is the master, go to the Settings… -> Advanced… -> 0 0 0 0 -> Linked Devices… -> Devices… menu

Eddi

  1. Press the “X” button to access the Main Menu
  2. Use the arrow and “tick” buttons to move through the menus
    • Settings… -> Advanced… -> 0 0 0 0 -> Linked Devices… -> Devices… -> Hub…
  3. Select “Delete Device…”

Zappi v1

  1. Press the “X” button to access the Main Menu
  2. Use the arrow and “tick” buttons to move through the menus
    • Settings… -> Advanced… -> 0 0 0 0 -> Linked Devices… -> Devices… -> Hub…
  3. Select “Delete Device…”

Zappi v2

  1. Press the left hand “pizza box” menu button to access the Main Menu
  2. Use the arrow and “tick” buttons to move through the menus
    • Settings… -> Advanced… -> 0 0 0 0 -> Linked Devices… -> Devices… -> Hub…
  3. Select “Delete Device…”

(2) Updating the firmware on the hub

To make sure you have the latest firmware on your hub

  1. Unplug the power to the hub
  2. Press and hold the download button
  3. Plug the power back in again while continuing to hold the download button
  4. Count to 5 slowly, then release the download button
  5. The “server” LED should turn white or red for a up to 30 seconds (may be a lot longer if the server is heavily loaded – please be patient). When the firmware on the hub as been updated the server light will return to blue or green.

(3) Pairing the new hub

If you have more than one myenergi device then pair the new hub with the master device (see above).

Eddi

  1. Plug in the hub and make sure that the power light is green
  2. Now put the hub into pairing mode by briefly pressing the “pair” button.
    • The power light on the hub will flash red and the “harvi / Ch 1” LED should be blue
  3. On the Eddi, pair with the new hub
    • From the main (graphic) screen, press the “X” button to put the Eddi into Pairing Mode
    • Use the down arrow and the “tick” button to select the following menu: Settings… -> Advanced… -> 0 0 0 0 -> Linked Devices… -> Pairing Mode…
  4. The new hub should appear on the list of devices.  Make sure it is selected and then press the “tick” button
  5. The screen will say “Updating Devices” before returning to the “Devices” screen where the hub should now be listed
  6. Keep pressing “X” to return to the main (graphic) screen
  7. The Eddi light on the hub should now be lit (green or blue)

Zappi v1

  1. Plug in the hub and make sure that the power light is green
  2. Now put the hub into pairing mode by briefly pressing the “pair” button.
    • The power light on the hub will flash red and the “harvi / Ch 1” LED should be blue
  3. On the Zappi, pair with the new hub
    • From the main (graphic) screen, press the “X” button to put the Zappi into Pairing Mode
    • Use the down arrow and the “tick” button to select the following menu: Settings… -> Advanced… -> 0 0 0 0 -> Linked Devices… -> Pairing Mode…
  4. The new hub should appear on the list of devices.  Make sure it is selected and then press the “tick” button
  5. The screen will say “Updating Devices” before returning to the “Devices” screen where the hub should now be listed
  6. Keep pressing “X” to return to the main (graphic) screen
  7. The Zappi light on the hub should now be lit (green or blue)

Zappi v2

  1. Plug in the hub and make sure that the power light is green
  2. Now put the hub into pairing mode by briefly pressing the “pair” button.
    • The power light on the hub will flash red and the “harvi / Ch 1” LED should be blue
  3. On the Zappi, pair with the new hub
    • From the main (graphic) screen, press the left hand (“pizza box”) menu button to put the Zappi into Pairing Mode
    • Use the down arrow and the “tick” button to select the following menu: Settings… -> Advanced… -> 0 0 0 0 -> Linked Devices… -> Pairing Mode…
  4. The new hub should appear on the list of devices.  Make sure it is selected and then press the “tick” button
  5. The screen will say “Updating Devices” before returning to the “Devices” screen where the hub should now be listed
  6. Keep pressing the left hand (“pizza box”) menu button to return to the main (graphic) screen
  7. The Zappi light on the hub should not be lit (green or blue)

 

If you have any problems pairing the new hub then please contact the myenergi technical support at support@myenergi.uk and we will help you complete the process.